IoT connectivity comparison: Wi-Fi, LTE-M, NB-IoT or LoRaWAN
Hephaestus Technology6 min read

The right IoT connectivity depends on four things: where the device is, how much data it sends, how it is powered and who runs the network. Wi-Fi suits mains-powered devices inside buildings that already have a network. LTE-M suits battery or mobile devices that need wide coverage, moderate data and firmware updates. NB-IoT suits static devices sending tiny messages, often deep indoors. LoRaWAN suits long-range, very low-data sensors where you can use a public network or install your own gateways.
Key takeaways
- Start from the deployment site, data volume and power source, not from the technology.
- LTE-M and NB-IoT are licensed cellular standards from 3GPP; the GSMA counts 129 LTE-M and 140 NB-IoT commercial networks worldwide.
- LoRaWAN runs in unlicensed spectrum, which means no SIM, but you depend on public network coverage or your own gateways.
- Wi-Fi offers high data rates at low connectivity cost but needs local access points and more power.
- Test real coverage at your actual deployment sites before you commit to a design.
What are the main IoT connectivity options?
IoT connectivity is the radio technology a device uses to send data to the internet. For most European products the shortlist is Wi-Fi, Bluetooth Low Energy (usually via a phone or hub), the two cellular low-power standards LTE-M and NB-IoT, and LoRaWAN.
- Wi-Fi is the familiar local wireless network. Many embedded chips include it: Espressif's ESP32-S3, for example, integrates 2.4 GHz 802.11 b/g/n Wi-Fi and Bluetooth LE.
- LTE-M is, in the GSMA's description, the industry term for the eMTC technology standardised by 3GPP in Release 13, supporting relatively fast data throughput, mobility, roaming and potentially voice.
- NB-IoT is a 3GPP low-power wide-area technology that, according to the GSMA, improves power consumption, capacity and spectrum efficiency, especially in deep coverage.
- LoRaWAN is a low-power wide-area networking specification from the LoRa Alliance that runs in unlicensed radio bands.
IoT connectivity comparison: how do they stack up?
The table compares the four options on the factors that usually decide a product. Figures quoted are vendor or industry claims for favourable conditions, not guarantees for your device.
| Factor | Wi-Fi | LTE-M | NB-IoT | LoRaWAN |
|---|---|---|---|---|
| Spectrum | Unlicensed | Licensed (mobile operator) | Licensed (mobile operator) | Unlicensed |
| Who runs the network | You or your customer | Mobile operator | Mobile operator | Public operator or you |
| Range | Building scale | Wide area, operator coverage | Wide area, strong deep-indoor focus | Up to 15 km rural, per LoRa Alliance |
| Data volume | High | Moderate | Very low | Very low |
| Mobility | Limited | Supported, with roaming | Best for static devices | Possible, application dependent |
| Battery life claim | Mains or rechargeable typical | At least 10 years for many use cases (GSMA) | More than 10 years for many use cases (GSMA) | 10+ years (LoRa Alliance) |
| Firmware updates over the air | Easy | Practical | Slow, small payloads | Difficult |
| Ongoing cost | Usually none per device | SIM or connectivity plan | SIM or connectivity plan | Network subscription or own gateways |
Battery life claims depend heavily on how often the device transmits and in what signal conditions. Measure your own device rather than relying on headline figures.
How widely available are LTE-M and NB-IoT?
Cellular IoT is now a mature, widely deployed option. The GSMA's network launch tracker lists 129 LTE-M networks and 140 NB-IoT networks, 269 in total, last updated November 2025. The same list records Vodafone with both LTE-M and NB-IoT across a group of markets that includes Ireland and the United Kingdom.
The GSMA explains that the mobile industry focused on two complementary licensed standards because no single technology covers every low-power use case. In practice, many cellular modules support both LTE-M and NB-IoT, so you can choose per market or per operator.
National coverage is not the same as coverage in a specific basement or field. Ask operators for coverage information for your exact sites and test with real hardware.
When is LoRaWAN the better choice?
LoRaWAN is a good fit when devices send small, infrequent messages, sit in places with poor cellular coverage, and you want to avoid per-device SIM costs. Farms, campuses, utilities and buildings with many sensors are common examples. The LoRa Alliance describes a star-of-stars architecture of end devices, gateways, a network server and application servers, and states that LoRaWAN is an ITU-approved international standard.
The trade-offs are real. Data rates are low, so large firmware updates are difficult. Because the bands are unlicensed and shared with other equipment, airtime is scarce and interference is possible, so check the licence-exemption conditions in each market you sell into. And if public network coverage is thin in your area, you will need to install and maintain gateways yourself.
When is Wi-Fi enough?
Wi-Fi is enough when the device is mains-powered, sits inside a building with a reliable network, and the customer is willing to connect it. Smart home products, office equipment and retail displays often fall into this group. Connectivity has no per-device fee, and high data rates make large firmware updates easy.
The main costs are setup and support. Onboarding a device onto a customer's network is a frequent source of support tickets, and corporate networks can block devices. Plan the provisioning experience as carefully as the hardware.
How do you choose for your product?
Work through these questions in order.
- Is the device mains-powered and indoors with existing Wi-Fi? If yes, Wi-Fi (possibly with Bluetooth LE for setup) is the simplest choice.
- Does it move, cross borders or need regular firmware updates? LTE-M is usually the strongest fit.
- Is it static, deep indoors or underground, sending tiny messages? Consider NB-IoT, after checking local operator support.
- Is it a low-data sensor in an area with poor cellular coverage, deployed in numbers? Consider LoRaWAN with public or private gateways.
- Still unsure? Prototype with a module that supports more than one option and test at real sites.
Whatever you choose, plan for secure firmware updates: connected radio equipment sold in the EU has had to meet the Radio Equipment Directive cybersecurity requirements since 1 August 2025. Our guide to secure firmware updates for IoT devices explains how. Connectivity is one decision in the wider process described in our guide on how to build an IoT product, and the 10 to 1,000 units worked example shows how it affects production.
Frequently asked questions
What is the difference between LTE-M and NB-IoT?
Both are licensed low-power cellular standards from 3GPP. LTE-M supports higher data rates, mobility, roaming and potentially voice, so it suits trackers and devices needing firmware updates. NB-IoT focuses on very small messages and deep coverage, so it suits static meters and sensors.
Is LoRaWAN cheaper than cellular IoT?
It can be, because there is no SIM per device, but the comparison depends on scale. If public LoRaWAN coverage is not available, you pay to install and maintain gateways. Compare total cost over the product's life, including support.
Can one device support several connectivity options?
Yes. Many cellular modules support both LTE-M and NB-IoT, and many products combine Bluetooth LE for setup with Wi-Fi or cellular for data. Supporting more radios adds cost, power and certification work, so add them only when there is a clear need.
Does 2G or 3G shutdown affect IoT devices?
Yes, devices that rely on older networks stop working when operators switch them off. Check each operator's plans in your target markets and prefer LTE-M or NB-IoT for new designs that need long service lives.
How long does an IoT battery really last?
It depends on how often the device transmits, signal strength, sensor power and battery chemistry. Industry claims of 10 years or more apply to favourable use cases. Measure current consumption on your own hardware and calculate battery life from real data.
Choosing connectivity for a new device? Book a free 30-minute call with our IoT team.
Cover photo by Sergey Meshkov on Pexels.